Knowby
Wacker Neuson RTD-SC4 Trench Roller – Start-Up and Operation
How to start, operate and shut down the Wacker Neuson RTD-SC4 remote-controlled trench roller: pre-inspection, transmitter controls, operating distances, vibration, display screens and shutdown.
How to start, operate and shut down the Wacker Neuson RTD-SC4 remote-controlled trench roller: pre-inspection, transmitter controls, operating distances, vibration, display screens and shutdown.
1
Step 1 of 18

Read the manual and wear PPE

Before using any piece of Wacker Neuson equipment, always refer to the operator's manual and wear the proper personal protective equipment.

2
Step 2 of 18

Complete the pre-inspection check

Before starting the trench roller, complete a pre-inspection check of the machine:

  1. Do a visual inspection and get rid of any excess debris.

  2. Check the machine fluids, such as fuel and engine oil levels.

  3. Make sure you release the brake bar.

3
Step 3 of 18

Turn the battery disconnect on

To start up the machine:

  1. Open the rear hood.

  2. Remove the controller.

  3. Turn the battery disconnect to the ON position.

This turns the safety beacon on.

4
Step 4 of 18

Close the hood and switch on the controller

  1. Close the hood and make sure the latches are secure.

  2. Turn the emergency stop button clockwise to release it and turn on the controller.

5
Step 5 of 18

Check the radio signal

Check the radio signal bars to make sure there is a connection between the controller and the transceiver.

6
Step 6 of 18

Start the engine

Press and hold the engine start button for 3 seconds to start the engine.

7
Step 7 of 18

Keep the correct distance

  • To put the machine in drive, you must stay at least 6.5 ft (2 m) from the machine. The transmitter will notify you if you are too close to operate.

  • You must stay within 98 ft (30 m) of the machine. Outside that distance, machine movement stops but the engine remains running.

8
Step 8 of 18

Steer and drive with the paddles

  • The paddle on the left side controls steering left or right.

  • The paddle on the right side controls driving forward or reverse.

9
Step 9 of 18

Set the engine speed

Use this switch to change the engine speed between low and auto.

  • In auto, you can travel at high speed if the vibration is off.

  • To activate high speed, push the driving paddle fully forward or backward.

  • Auto mode also activates auto idle.

10
Step 10 of 18

Auto idle

  • After 5 seconds of no travel activity, the engine throttles down to idle.

  • If vibration is on, the engine throttles down to idle after 20 seconds of no travel activity and the vibration shuts off.

11
Step 11 of 18

Control the vibration

One switch selects low or high vibration. The other switch turns vibration on and off.

12
Step 12 of 18

Horn and return to centre

  • On the right side, the top button activates the horn.

  • Below it is the button that turns the return to centre function on or off.

When it is turned on, the machine automatically returns to driving in a straight line once the steering paddle is released.

13
Step 13 of 18

Pairing screen

The bottom screen is used to pair the transmitter to the machine.

14
Step 14 of 18

Top display screen

The top screen displays information such as:

  • machine hours

  • vibration status

  • travel speed

  • active faults, indications and warnings

  • engine speed

  • steering style

  • parking brake status

15
Step 15 of 18

Display sub-pages

Select the left or next button to toggle through the active sub-pages: machine parameters, active fault codes, maintenance settings and PIN code.

The PIN code sub-page is used by owners and hire companies only, once the machine has been thoroughly reviewed after a machine tip-over.

16
Step 16 of 18

Transmitter batteries

The transmitter is supplied with two batteries. While one is in the transmitter for operation, the other is on the onboard charger.

17
Step 17 of 18

Park and stop the engine

When you have finished using the machine:

  1. Park it on a flat, level surface.

  2. Set the vibration and travel speed switches to the down position.

  3. Press and hold the engine stop/start button for at least 3 seconds to shut the machine down.

18
Step 18 of 18

Stow the controller and isolate the battery

Put the controller back, turn the battery disconnect off and shut the rear hood.

If the battery disconnect is not turned off, the beacon stays on to remind the operator that the machine is not fully shut down.