Knowby
Wacker Neuson DV60 – Changing the Skip Safely
How to safely set down, pick up and reconnect a skip on the Wacker Neuson DV60 with skip changing system: support legs, the outside operator station, coupling checks, common errors and the display symbols. For trained and authorised operators only.
How to safely set down, pick up and reconnect a skip on the Wacker Neuson DV60 with skip changing system: support legs, the outside operator station, coupling checks, common errors and the display symbols. For trained and authorised operators only.
1
Step 1 of 22

Before you start

The dumper may only be operated by trained and authorised personnel.

  • Always wear your personal protective equipment.

  • Keep the danger zone clear of people and other machines.

  • If anyone enters the danger zone, stop work immediately.

2
Step 2 of 22

Unload a skip carried on top

For transport, the skips may be lashed together. To unload the skip carried on top and position it correctly:

  1. Securely attach it to a lifting device such as a crane or excavator, using the designated lifting points on the skip.

  2. Lift it in a controlled manner off the skip below, which stays firmly in place.

3
Step 3 of 22

Fit the support legs before setting down

Insert the included support legs into the designated openings and secure them with bolts.

Caution: extend the support legs all the way to the designated markings. This is the only way to guarantee that the dumper can pick the skip up again. If the extension length is too short or too long, the skip cannot be picked up correctly.

4
Step 4 of 22

Operator station

The control unit is at the operator station next to the machine. You can carry out everything needed for the changeover from outside the cab.

Here you will find all the connections and the system for locking the skip in place.

5
Step 5 of 22

Before changing the body

Make sure that:

  • the sub-base is level and stable

  • the vehicle is level

  • the parking brake is engaged.

6
Step 6 of 22

Set down: release and disconnect

  1. Drive the vehicle with the skip attached to the unloading site.

  2. Release the lock using the change mode button.

  3. Carefully disconnect the hydraulic and electrical connections and hang them in the designated storage loops.

7
Step 7 of 22

Fit the side support legs

Insert the supplied side support legs into the designated ports and secure them with bolts. Repeat on the other side of the machine.

You can identify the side support legs by their right angle.

8
Step 8 of 22

Fit the front support legs

Repeat the process with the support legs at the front of the skip. Use the legs that face forward and have a larger angle.

Extend these legs to the correct length and secure them immediately after installation.

9
Step 9 of 22

Raise the hopper

Activate the lifting cylinder by pressing the two-hand control button and the unlock button at the same time.

You will hear and see the cylinder under the hopper, and the hopper rises.

10
Step 10 of 22

Extend the side support legs

The side support legs can now also be extended and locked into place.

11
Step 11 of 22

Lower the cylinder and drive out

  1. Once all the legs are locked in place, lower the cylinder by pressing the two-hand control button and the lock button at the same time.

  2. Carefully drive the machine out from under the skip.

Caution: retract the cylinder until it is fully compressed before driving the machine away.

12
Step 12 of 22

Pick up: position the vehicle

  1. Position the vehicle exactly in front of the mounting points.

  2. As you drive under the parked skip, make sure the centre cylinder is visibly in the middle of the skip.

  3. Drive carefully and straight under the skip until you feel it stop.

13
Step 13 of 22

Check the lifting hooks

The lifting hooks must engage securely in the openings. Then carry out a visual inspection.

14
Step 14 of 22

Raise the hopper to couple

To couple the skip successfully, follow these steps in sequence.

  1. Press the change mode button.

  2. Raise the hopper by pressing the two-hand control and unlock buttons at the same time. This extends the cylinder and raises the hopper.

15
Step 15 of 22

Retract the side legs and lower the skip

Retract the side support legs, then lower the skip by pressing the two-hand control and lock buttons at the same time.

16
Step 16 of 22

Remove the support legs

Retract the front support legs and remove all four legs from the skip. Place them in a safe location.

17
Step 17 of 22

Reconnect the skip

  1. Connect the hydraulic and electrical connections to the machine, paying attention to the colour-coded markings.

  2. Press the change mode button again to complete the connection.

18
Step 18 of 22

Check the skip is attached

  • Check on the display in the cab that the skip is securely attached: the green coupling symbol lights up.

  • Check that the hydraulics are working properly and listen for any unusual noises.

19
Step 19 of 22

Common errors

The most common errors are:

  • the skip positioned at an angle

  • an attachment that is not locked properly

  • movements that are too fast and jerky.

20
Step 20 of 22

If the machine cannot get under the skip

If the machine cannot be manoeuvred under the skip, it is probably equipped with Active Sense Control.

Temporarily disable it by holding down the Active Sense Control button on the right armrest for two seconds.

21
Step 21 of 22

Regular checks

For safe and long-lasting operation, check the skip changing system regularly. Pay particular attention to:

  • the locking mechanism

  • the hydraulic lines

  • cleanliness in the loading area.

22
Step 22 of 22

Display symbols

The dumper's display shows four symbols for the skip changing system. In the order shown in the clip:

  1. The interchangeable body is locked in place and ready for operation.

  2. Swap mode has been activated.

  3. The interchangeable body is unlocked.

  4. The connection to the interchangeable body is incomplete.