Knowby
Wacker Neuson WL36 Wheel Loader – Routine Servicing
Routine service points on the Wacker Neuson WL36 wheel loader: fuel, lifting the cab, battery, differentials, air filter, engine oil, hydraulics, coolant, fuel filters, U-joints, tyres and planetary gears. Always adhere to the warnings and cautions in the operator's manual.
Routine service points on the Wacker Neuson WL36 wheel loader: fuel, lifting the cab, battery, differentials, air filter, engine oil, hydraulics, coolant, fuel filters, U-joints, tyres and planetary gears. Always adhere to the warnings and cautions in the operator's manual.
1
Step 1 of 21

Fill with fuel

The fuel fill point is on the front right-hand side of the machine.

Only use low sulphur or ultra-low sulphur diesel.

After filling, turn the cap until it clicks to ensure a tight seal.

2
Step 2 of 21

Remove the cab bolts

To lift the cab, remove the two 24 mm bolts that secure the cab to the frame:

  • One on the exterior

  • One on the interior

3
Step 3 of 21

Release and tilt the engine hood

  1. Pull the release lever located inside the machine to release the engine hood.

  2. Tilt the hood back for access to the engine and to the jack.

4
Step 4 of 21

Close both doors

Make sure both doors are closed before jacking up the cab.

Use the release lever found inside to close the door.

5
Step 5 of 21

Set up the jack

  1. Locate the jack bar mounted to the air filter frame.

  2. Make sure that the jack is selected in the up position.

6
Step 6 of 21

Jack up the cab

Jack the cabin up until the locking mechanism has fallen into place.

7
Step 7 of 21

Remove the battery cover bolts

To access the battery, remove the two 10 mm bolts that hold down the access cover.

8
Step 8 of 21

Pull away the access cover

Once the bolts are removed, pull away the access cover.

Save the cover and the bolts for reinstallation later.

9
Step 9 of 21

Access the rear differential

The rear differential is accessed from the back of the machine.

A half-inch ratchet can be used to remove the fill and drain plugs.

10
Step 10 of 21

Change the differential oil

The fill port and drain port are marked on the rear and front differentials.

When changing the front or rear differential oil, use a 90 weight gear oil.

Always follow the safety warnings in the manual.

Do not perform maintenance or service tasks under raised loader lift arms until the loader lift arm support device has been inserted and locked.

11
Step 11 of 21

Check the air filter

  1. Remove the three clasps that secure the filter cover to the filter body.

  2. Check the filter.

The filter should be checked on a daily basis and replaced when necessary.

12
Step 12 of 21

Engine oil

  • Check the oil daily and replenish when necessary.

  • After the first 50 hours of operation, change the engine oil and the engine oil filter.

  • Each subsequent oil change should be done in 500-hour increments.

  • Only use 10W-40 oil when the ambient temperature is −4 to 104 °F (−20 to 40 °C). Outside this range, consult the engine manufacturer.

13
Step 13 of 21

Check the hydraulic fluid level

Check the hydraulic fluid level daily and replenish with ISO VG 46 hydraulic oil.

14
Step 14 of 21

High-pressure hydraulic filter

Replace the high-pressure hydraulic filter initially at 500 hours and as needed after that.

15
Step 15 of 21

Return hydraulic filter

Replace the return hydraulic filter initially at 500 hours and every 1,000 hours after that.

The return filter cap and the reservoir cap are labelled in the clip.

16
Step 16 of 21

Check the engine coolant

Check the engine coolant level daily and replace the coolant every two years.

Only use a heavy-duty ethylene glycol that meets the ASTM D4985 specification.

17
Step 17 of 21

Fuel filters

Change the fuel filter and the fuel pre-filter initially at 500 hours.

Each subsequent change should be done at 1,000-hour intervals.

18
Step 18 of 21

Lubricate the U-joints

Use a multi-purpose, water-resistant grease to lubricate the U-joints every 250 hours.

The front and rear U-joints have grease fittings.

19
Step 19 of 21

Check the tyre pressure

Check the air pressure daily.

Consult the operator's manual for the correct value.

20
Step 20 of 21

Planetary gear oil

  1. Use a half-inch ratchet to remove the plug.

  2. Fill the planetary gear with 90 weight gear oil.

21
Step 21 of 21

Lubrication points

The diagram and table show the machine's lubrication points.