Knowby
DRAWER & STOWLOK, FITTING, UTE
Fitting manual for drawer and Stowlok on a ute.
Fitting manual for drawer and Stowlok on a ute.
1
Step 1 of 21
2
Step 2 of 21

​Components List​

​Tools List​

​Drilling Guide​

​Drawer Positioning​

​Carcase Fixing​

​Low Profile Bar Installation​

​Clean Up​

​QA Sheet​

3
Step 3 of 21
4
Step 4 of 21
5
Step 5 of 21
6
Step 6 of 21
<p><span style="font-size: 18px; line-height: 1.4;">Find the correct vehicle in the list below, then use its low-profile bar position (A–F) and drill position (1–3).</span></p><p></p><p><span style="font-size: 18px; line-height: 1.4;">Mitsubishi Triton 2024 - F(Low-Profile Bar position), 2 (Drill)</span></p><p></p><p><span style="font-size: 18px; line-height: 1.4;">Nissan Navara - B(Low-Profile Bar position), 2 (Drill)</span></p><p></p><p><span style="font-size: 18px; line-height: 1.4;">Ford Ranger - F(Low-Profile Bar position), 3 (Drill)</span></p><p></p><p><span style="font-size: 18px; line-height: 1.4;">Toyota Hilux - F(Low-Profile Bar position), 2 (Drill)</span></p><p></p><p><span style="font-size: 18px; line-height: 1.4;">BYD Shark 6 - B(Low-Profile Bar position), 2 (Drill)</span></p><p></p><p><span style="font-size: 18px; line-height: 1.4;">Izuzu D-Max / Madza BT-50 - C(Low-Profile Bar Position), 1 (Drill)</span></p><p></p>

Find the correct vehicle in the list below, then use its low-profile bar position (A–F) and drill position (1–3).

Mitsubishi Triton 2024 - F(Low-Profile Bar position), 2 (Drill)

Nissan Navara - B(Low-Profile Bar position), 2 (Drill)

Ford Ranger - F(Low-Profile Bar position), 3 (Drill)

Toyota Hilux - F(Low-Profile Bar position), 2 (Drill)

BYD Shark 6 - B(Low-Profile Bar position), 2 (Drill)

Izuzu D-Max / Madza BT-50 - C(Low-Profile Bar Position), 1 (Drill)

7
Step 7 of 21
<p>Fit low profile bar (CP102260) on carcase before fitting following fitting guide in previous step.</p>

Fit low profile bar (CP102260) on carcase before fitting following fitting guide in previous step.

8
Step 8 of 21
<p>Slide a channel nut into the low profile bar on each side.</p><p>Put an M8 spring washer, then an M8 washer, on an M8 x 25 bolt. Thread the bolt into the channel nut and tighten until secure.</p>

Slide a channel nut into the low profile bar on each side.

Put an M8 spring washer, then an M8 washer, on an M8 x 25 bolt. Thread the bolt into the channel nut and tighten until secure.

9
Step 9 of 21

Open the tailgate and all canopy doors.

Use a forklift to lift the drawer unit into the bed.

10
Step 10 of 21
<p>Check that the Z-bar lines up with the rear of the bed.</p>

Check that the Z-bar lines up with the rear of the bed.

11
Step 11 of 21
<p>Close the tailgate and check there is enough clearance between it and the drawers.</p>

Close the tailgate and check there is enough clearance between it and the drawers.

12
Step 12 of 21
<p>Measure the gap between the drawer unit and the side of the bed, on both sides.</p><p>The two gaps should be the same. If they aren't, slide the unit sideways until it is centred.</p>

Measure the gap between the drawer unit and the side of the bed, on both sides.

The two gaps should be the same. If they aren't, slide the unit sideways until it is centred.

13
Step 13 of 21

Check underneath that no wiring is in the way before drilling.

Drill an 8mm hole on each side of the carcase, where shown, all the way through the bed floor (2 holes).

14
Step 14 of 21

Spray both holes with soft seal.

Put an M8 washer on an M8 x 35 bolt and push it down through each hole.

15
Step 15 of 21
<p>From under the vehicle, fit an M8 washer and an M8 Nyloc nut to each bolt, then tighten.</p>

From under the vehicle, fit an M8 washer and an M8 Nyloc nut to each bolt, then tighten.

16
Step 16 of 21
<p>Check underneath that no wiring is in the way before drilling.</p><p>Drill an 8mm hole approximately 50mm from the interior edge of the drawer on each side of the low profile bar, all the way through the bed floor. (Distance may vary depending on vehicle) </p><p>Spray both holes with soft seal.</p><p></p>

Check underneath that no wiring is in the way before drilling.

Drill an 8mm hole approximately 50mm from the interior edge of the drawer on each side of the low profile bar, all the way through the bed floor. (Distance may vary depending on vehicle)

Spray both holes with soft seal.

17
Step 17 of 21

Push an M8 x 50 bolt with an M8 washer down through each hole in the low profile bar (CP102260).

From under the vehicle, fit an M8 washer and an M8 Nyloc nut to each bolt, then tighten.

Note: Depending on the vehicle, you may need a spacer between the low profile bar and the bed.

18
Step 18 of 21

Remove all the drawer dividers and clean the whole drawer assembly.

19
Step 19 of 21

Refit all the drawer dividers.

20
Step 20 of 21
<p>Fitting complete.</p><p>Fill in the QA sheet provided.</p>

Fitting complete.

Fill in the QA sheet provided.

21
Step 21 of 21
<p>Please fill out the hard copy QA sheet included with the product you got.</p><p>Once filled out, please send it back to</p><p><a target="_blank" rel="noopener noreferrer nofollow" href="mailto:charl@camcoindustries.co.nz">charl@camcoindustries.co.nz</a></p><p>If you have issues with instructions and need assistance, please contact.</p><p>&nbsp;</p><p>If the hard copy does not arrive, please contact us.</p><p><a target="_blank" rel="noopener noreferrer nofollow" href="mailto:charl@camcoindustries.co.nz">charl@camcoindustries.co.nz</a></p><p>0800 663 500</p>

Please fill out the hard copy QA sheet included with the product you got.

Once filled out, please send it back to

charl@camcoindustries.co.nz

If you have issues with instructions and need assistance, please contact.

 

If the hard copy does not arrive, please contact us.

charl@camcoindustries.co.nz

0800 663 500