Knowby
Wacker Neuson DV90 Dual View Dumper – Daily Checks
Operator pre-use checks for the Wacker Neuson DV90 Dual View dumper: walk-around, engine compartment and fluids, cab and controls, then brake, steering and hydraulic function tests. Ends with the additional weekly checks. Record and report any faults or damage immediately.
Operator pre-use checks for the Wacker Neuson DV90 Dual View dumper: walk-around, engine compartment and fluids, cab and controls, then brake, steering and hydraulic function tests. Ends with the additional weekly checks. Record and report any faults or damage immediately.
1
Step 1 of 47

Park safely

Before the pre-use or daily checks, make sure the machine is securely parked in a safe area, on level, firm ground.

Always keep the key with you.

2
Step 2 of 47

Wear the required PPE

All the required PPE must be worn:

  • Hard hat

  • Safety glasses

  • Hi-vis long-sleeve top

  • Hi-vis trousers

  • Resistant gloves

  • Safety boots

3
Step 3 of 47

Walk around the machine

Before starting your shift, carry out a thorough walk-around of your machine.

Record and report any faults or damage immediately.

4
Step 4 of 47

Moving parts and connections

Check all moving parts and connections are secure.

5
Step 5 of 47

Hoses

Check all hoses are secure, with no signs of leaks or damage.

6
Step 6 of 47

Tyres and rims

  • Check the tyres are in good condition and suitably inflated.

  • Check all four rims for damage and wear.

  • Check the inside tyre walls as well.

7
Step 7 of 47

Tyre pressures

If the tyre pressures look low during your visual check, check them with a gauge.

Re-inflate only if you are trained to do so.

8
Step 8 of 47

Wheel nut indicators

Check all wheel nut indicators are aligned.

9
Step 9 of 47

Cameras

Check the cameras are clean and not obstructed.

10
Step 10 of 47

Mirrors

Check the mirrors are in good condition and not damaged.

11
Step 11 of 47

Windows

Check all windows are in good condition and clean.

12
Step 12 of 47

Cab, ROPS and FOPS

Check the cab and the protective structures (ROPS and FOPS) for damage.

13
Step 13 of 47

Guards

Check all guards are in good condition and free from damage.

14
Step 14 of 47

Engine compartment and fluids

For these checks, make sure the engine is switched off and has cooled down.

CAUTION: Hot components can cause burns.

15
Step 15 of 47

Engine access bay

Open the engine access bay on the right of the machine.

16
Step 16 of 47

Radiators

Check the radiators for dirt. If necessary, make sure they are cleaned to avoid damage to the engine.

17
Step 17 of 47

Coolant level

Check the coolant level is visible in the sight glass.

If the coolant level is low, coolant must be added.

18
Step 18 of 47

Topping up coolant

  1. Take care when removing the radiator cap.

  2. Slowly release the pressure from the system before removing the cap fully.

  3. Once the system is topped up, fully secure the cap again.

19
Step 19 of 47

Air filter

Check the air breather element: squeeze the rubber grommet at the bottom of the air filter and make sure no excess debris comes out.

20
Step 20 of 47

Insulating mats

Check the insulating mats in the engine compartment for any signs of damage.

21
Step 21 of 47

Engine oil level

  1. Remove the dipstick and wipe off any excess oil with a clean cloth.

  2. Reinsert the dipstick, then remove it again.

  3. Check the oil level is between the minimum and maximum marks.

22
Step 22 of 47

Fuel system: before draining

Water must be drained from the fuel system.

Where fluid could spill or leak, put suitable containment equipment in place to minimise any contamination of the ground or the environment.

23
Step 23 of 47

Drain water from the fuel filter

  1. Open the drain valve at the bottom of the fuel filter.

  2. Drain the water into a suitable container.

  3. Once fuel appears instead of water, close the drain valve.

24
Step 24 of 47

Dispose of fluids and rags

All excess fluids and any cloths or rags used must be disposed of safely and in accordance with site rules.

25
Step 25 of 47

Brake fluid level

Check the brake fluid level in the reservoir is at the level indicated.

If the level is below the level indicator, hydraulic oil must be added.

26
Step 26 of 47

Hydraulic oil: before checking

  • Park the machine on level ground with the engine switched off.

  • Release the pressure from the hydraulic system and isolate the machine.

27
Step 27 of 47

Hydraulic oil level

Check the sight glass on the left of the machine. The oil level must be in the middle of the sight glass.

If the level is too low, record and report it, as it will need topping up.

28
Step 28 of 47

Steps and handrails

Check the steps and handrails are secure and free from debris, and check for any signs of damage.

29
Step 29 of 47

Getting on and off

Always use three points of contact when mounting or dismounting the machine, and always face the machine.

30
Step 30 of 47

Operator seat

Check the operator seat is in the correct position and adjust it as needed.

31
Step 31 of 47

Mirror adjustment

Check all mirrors are correctly adjusted to give maximum visibility.

32
Step 32 of 47

Seat belt

  • Check the seat belt is in good condition: the webbing is not frayed or cut and the fasteners are secure.

  • Check the buckle is in good condition and locks into place correctly.

33
Step 33 of 47

Seat swivel

Make sure the seat swivel function is fully operational and the seat is locked in its final position.

34
Step 34 of 47

Gauges and switches

Check all gauges and switches for signs of damage.

35
Step 35 of 47

Horn and reversing signal

Check the horn and the reversing signal are working.

36
Step 36 of 47

Lights, indicators and beacons

Turn on all machine lights, indicators and flashing beacons. Check they are clean and working properly.

37
Step 37 of 47

Gauges with the engine running

With the engine started, check for any faulty gauges.

38
Step 38 of 47

Parking brake test

Make sure the skip is lowered and the engine is started.

  1. Apply the parking brake.

  2. Engage speed range 1 and select a direction.

  3. Press the accelerator for at least 5 seconds.

The machine must not move.

39
Step 39 of 47

Foot brake test

  1. Press the foot brake firmly.

  2. Release the parking brake.

  3. Engage speed range 1 and select a direction.

  4. Press the accelerator for at least 5 seconds.

The brake pedal must not give way and the machine must not move.

40
Step 40 of 47

Drive and steering test

  1. When it is safe to do so, move the machine forward slowly and steer in both directions.

  2. Bring the machine to a safe and controlled stop.

  3. Apply the parking brake and put the machine into neutral.

41
Step 41 of 47

Hydraulics: raise the skip

When it is safe to do so, with the parking brake applied and the machine in neutral, slowly raise the skip fully.

If a swivel skip is fitted, rotate it both left and right.

42
Step 42 of 47

Hydraulics: ram and rod

While the skip is fully raised, check the hydraulic ram and rod from the cab for any signs of wear or damage.

Lower the skip back into its default position.

43
Step 43 of 47

Weekly checks

These checks are in addition to the daily checks.

Before starting them, make sure the skip is in the raised position with the safety bar engaged.

44
Step 44 of 47

Weekly: lubrication

Lubricate the machine in line with the manufacturer's recommendations.

Some machines are fitted with an auto-lubrication system. This may not cover all the required lubrication points.

45
Step 45 of 47

Weekly: axle mountings

Visually check the axle mountings for tightness.

46
Step 46 of 47

Weekly: access and egress

Check the access and egress points of the machine are free from obstructions and damage.

Record and report any defects immediately.

47
Step 47 of 47

If in doubt, stop

  • Refer to the operator manual if you need further clarification. It is kept in the cab.

  • If you are still in doubt, or have any safety concerns, stop what you are doing immediately.

  • Isolate the machine and seek advice from your supervisor.