Knowby
Wacker Neuson WL28 Wheel Loader – Drive and Work Modes
Drive and work modes on the Wacker Neuson WL28 wheel loader for continuous flow attachments such as brooms and snow blowers: joystick and auxiliary controls, auto (eco) mode, manual throttle and speed limiter, and attachment mode.
Drive and work modes on the Wacker Neuson WL28 wheel loader for continuous flow attachments such as brooms and snow blowers: joystick and auxiliary controls, auto (eco) mode, manual throttle and speed limiter, and attachment mode.
1
Step 1 of 13

Joystick basics

  • Forward, neutral and reverse are selected on the joystick.

  • The two-speed switch is right underneath that control: low range and high range (turtle and rabbit).

2
Step 2 of 13

Auxiliary hydraulics

  • The proportional auxiliaries are on the front side of the joystick.

  • The continuous flow auxiliaries are also started with a command on that switch.

  • To activate continuous flow, use the switch in the switch bank marked with the Roman numeral III and an arrow going around it: third circuit continuous flow.

3
Step 3 of 13

Why the mode matters

The machine is fully hydrostatic: the same oil supplies the travel drive, the work group and the auxiliary hydraulics.

The modes operate differently, which gives you flexibility to work in a comfortable and efficient manner.

4
Step 4 of 13

Auto mode: activate continuous flow

Auto (eco) mode is the standard operating mode.

To run a continuous flow attachment, first activate third circuit continuous flow by pressing the switch in the cab.

The indicator flashes green.

5
Step 5 of 13

Lock in continuous flow

  1. While the button is flashing, select the direction of flow. This locks in continuous flow.

  2. Pull the trigger on the front side of the joystick: the system is idle and waiting.

  3. Pull the joystick trigger again for continuous flow.

6
Step 6 of 13

Give the attachment oil flow

In auto mode, increase the engine rpm with the right foot pedal to send more oil to the attachment.

Modulate travel speed with the inch brake pedal.

7
Step 7 of 13

Drive two-footed in auto mode

  1. Speed up the engine with the accelerator pedal (right foot) to supply oil to the attachment.

  2. Put the machine in forward drive.

  3. Ease off the inch brake pedal with your left foot to move.

Reverse works the same way.

8
Step 8 of 13

Give your feet a break: manual controls

In auto (eco) mode you can instead use the manual throttle control and the speed limiting lever.

  • The manual throttle lever controls engine speed in place of the foot pedal.

  • The manual speed control lever sets the travel speed.

9
Step 9 of 13

Set the travel speed by hand

  1. Put the machine in forward travel drive.

  2. Increase the speed on the speed limiter until the machine moves.

  3. Adjust the travel speed up and down using just that hand lever.

10
Step 10 of 13

Attachment mode: when to use it

Attachment mode is an additional operating mode. It is the mode to choose for a broom or a snow blower:

  • It constantly supplies oil to the attachment.

  • You control the travel speed fully with the right foot pedal.

11
Step 11 of 13

Select attachment mode

  1. Apply the park brake and put the machine in neutral.

  2. Switch over to attachment mode.

  3. Increase the engine rpm with the manual throttle control. Attachment mode requires it.

  4. Select the travel direction.

  5. Control your speed with the right foot pedal.

12
Step 12 of 13

Oil priority for spinning attachments

Attachment mode always prioritises oil to the attachment, which makes it a great mode for spinning attachments.

You control the speed of the rotating attachment and still have full control of travel speed with your right foot.

13
Step 13 of 13

Low and high range

Attachment mode works in the low (turtle) speed range and in the high range.

You have full travel speed adjustment while oil flow priority to the attachment is maintained.