Knowby
Wacker Neuson Telehandlers – Operation
Operating Wacker Neuson telehandlers: PPE, pre-start checks, setting up the workstation, starting and driving, lifting and telescoping, load limit and overload cut-off, the Vertical Lift System (VLS), changing attachments, steering modes and safe parking.
Operating Wacker Neuson telehandlers: PPE, pre-start checks, setting up the workstation, starting and driving, lifting and telescoping, load limit and overload cut-off, the Vertical Lift System (VLS), changing attachments, steering modes and safe parking.
1
Step 1 of 22

Wear your PPE

Wear the personal protective equipment required for this machine at all times. This is for your own safety.

  • Helmet: protects from falling objects on the construction site

  • Protective gloves: prevent injuries to the hands

  • Safety shoes with integrated steel toe caps: protect your feet

  • Safety glasses: protect your eyes from flying particles

  • Ear protection: protects your ears and eardrums

2
Step 2 of 22

Check the tyre pressure

Check the tyre pressure with an air pressure gauge.

Refer to the operating instructions for the correct value.

3
Step 3 of 22

Turn on the battery disconnect switch

Turn the battery disconnect switch to the position shown.

The machine is now ready for operation.

4
Step 4 of 22

Secure the window

When opening the window, make sure that it is correctly secured with a firm click.

5
Step 5 of 22

Set up your workstation

  1. Adjust the seat to suit your body size and weight.

  2. Adjust the steering wheel for tilt and height.

  3. Adjust the mirrors so that you always have a clear view.

  4. Fasten your seat belt.

6
Step 6 of 22

Start the engine

Turn the ignition key to start the engine.

On machines with a mechanical handbrake lever, make sure it is engaged before starting the engine.

7
Step 7 of 22

Release the handbrake

Step on the brake pedal before releasing the handbrake.

8
Step 8 of 22

Select the direction of travel

Select forward or reverse with the orange thumb wheel on the joystick.

9
Step 9 of 22

Lock the lifting arm for road travel

To switch off the hydraulic functions of the lifting arm for road travel, press the red key shown.

10
Step 10 of 22

Lift and lower with the joystick

The basic functions of lifting, lowering, retracting and extending are controlled with the joystick.

11
Step 11 of 22

Telescope the arm

The second, grey thumb wheel on the joystick controls the telescopic cylinder.

12
Step 12 of 22

Watch the load limit

When the machine approaches its load limit, an audible and visual warning is given.

Always move loads as close to the machine and as low down as possible.

13
Step 13 of 22

Overload cut-off

To deactivate the overload cut-off for a short time, press and hold the button.

Attention: there is a risk of tipping over.

14
Step 14 of 22

Use VLS stacking mode

The Vertical Lift System (VLS) is an assistance system for greater safety and comfort.

In stacking mode, the machine automatically telescopes the arm out and guides the load upwards close to vertical.

When lowering, the telescopic arm is also retracted automatically to keep the load as close to the vehicle as possible.

15
Step 15 of 22

Use VLS bucket mode

Bucket mode is the second VLS mode.

Here, telescopic arm extension is not automated: you extend it manually.

When lowering, the telescopic arm is retracted automatically to keep the load as close to the vehicle as possible and avoid the risk of tipping over.

16
Step 16 of 22

Remove the attachment

  1. Press the two-hand control button and, at the same time, open the lock with the third control circuit.

  2. Park the attachment.

17
Step 17 of 22

Pick up the attachment

  1. Drive up to the attachment and pick it up with the quick hitch plate.

  2. Activate the third control circuit to lock the attachment.

  3. Check that the attachment is correctly locked.

18
Step 18 of 22

Connect hydraulic attachments

The hoses of hydraulic attachments, such as 4-in-1 buckets, can be connected to the couplings shown.

19
Step 19 of 22

Run the hydraulics continuously

For continuous hydraulic operation, press the button on the keypad and then select the flow direction on the joystick.

20
Step 20 of 22

Change the steering mode

  • Changing to all-wheel steering: the rear axle moves offset from the front axle.

  • Changing to front-wheel steering: the tyre position on the rear axle does not change.

  • Changing to crab steering: the rear axle moves in line with the front axle.

21
Step 21 of 22

Choose the right steering mode

  • All-wheel steering for optimum mobility

  • Front-wheel steering for road travel

  • Crab steering for precise manoeuvring

22
Step 22 of 22

Park the machine safely

  1. Place the bucket level on the ground.

  2. Switch the travel direction to neutral and secure the machine with the handbrake.

  3. Switch off the engine.

You will find detailed information in the operating instructions.