Knowby
Wacker Neuson Wheel Loaders – Operation
Operating Wacker Neuson articulated wheel loaders: PPE, getting on and starting, lights, raising the attachment, travel direction and speed, changing static and hydraulic attachments, switching off and driving safely. Always follow the operator's manual.
Operating Wacker Neuson articulated wheel loaders: PPE, getting on and starting, lights, raising the attachment, travel direction and speed, changing static and hydraulic attachments, switching off and driving safely. Always follow the operator's manual.
1
Step 1 of 18

Wear your PPE

Wear the personal protective equipment required for this machine at all times. This is for your own safety.

  • Safety shoes with integrated steel toe caps to protect your feet

  • A safety vest, so you stay highly visible on the job site at all times

2
Step 2 of 18

Climb onto the wheel loader

Climbing onto the wheel loader safely is simple: always keep at least three points of contact with the machine.

3
Step 3 of 18

Fasten the seat belt

Once seated, fasten the safety belt.

4
Step 4 of 18

Start the engine

  1. Insert the key into the ignition lock and turn it one position forwards for preheating.

  2. To start, turn it completely.

5
Step 5 of 18

Switch on the lighting

Switch on the lighting as shown:

  • Road lighting

  • Work light

  • Rotating beacon

Do not use the work lights in road traffic.

6
Step 6 of 18

Use the indicator

The indicator is located on the left side of the steering wheel.

7
Step 7 of 18

Raise the attachment before driving

Before you drive, the attachment must be raised.

  • Carefully pull the joystick backwards to raise it.

  • Move the joystick left or right to roll the attachment in or out.

8
Step 8 of 18

Select the travel direction

Use the orange wheel on the joystick to select forward or reverse.

A small arrow on the display shows the travel direction.

9
Step 9 of 18

Choose the speed range

Choose between rabbit for high speed and turtle for normal speed.

10
Step 10 of 18

Know the pedals

There are two drive pedals in the footwell:

  • The throttle pedal on the right

  • The inch brake pedal on the left

11
Step 11 of 18

Release an attachment

Wheel loaders use static and hydraulic attachments. To replace an attachment:

  1. Hold the release, then activate the rotary knob on the back of the joystick. This retracts the locating pin of the quick coupler system.

  2. Once the attachment is released, set it aside.

  3. Back the wheel loader out a bit.

12
Step 12 of 18

Connect a new attachment

  1. Tilt the quick coupler system forward and hook the attachment.

  2. Extend the locating pin again.

13
Step 13 of 18

Depressurise the hydraulic circuit

To replace a hydraulic attachment, you must also attach the hydraulic hoses.

Depressurise the hydraulic circuit using the touch button on the joystick console so that the couplings can be connected.

Caution: with pressure on the line, connecting the couplings may be difficult or impossible.

14
Step 14 of 18

Connect the hydraulic attachment

Once the couplings are released, connect the hydraulic attachment.

The hydraulic couplings must also be connected.

15
Step 15 of 18

Operate the hydraulic attachment

Once the hydraulic attachment is coupled, operate it via the third control circuit on the joystick control wheel.

The specific functions of each attachment are described in the operator's manual of that attachment.

16
Step 16 of 18

Switch off the wheel loader

  1. Lower the boom until the attachment lies horizontally on the ground.

  2. Pull the parking brake and turn the ignition key anticlockwise.

  3. Remove the key once the engine has completely stopped.

17
Step 17 of 18

Do not park on a slope

Make sure that the wheel loader is not parked on a slope.

18
Step 18 of 18

Drive with care

Caution: the wheel loader has articulated pendulum steering. The turning radius and the steering behaviour are different from a car.

When travelling, do not drive with the load raised.