Knowby
Strata - Install Guide
PRD-STR-004. Installing a Strata table on site: assemble the base upright, position it, lift the top on and fix it, then hand over. Includes dry-join tops. Applies to all Strata sizes.
PRD-STR-004. Installing a Strata table on site: assemble the base upright, position it, lift the top on and fix it, then hand over. Includes dry-join tops. Applies to all Strata sizes.
1
Step 1 of 10
<p>Check the site is ready:</p><ul><li><p>access</p></li><li><p>level floor</p></li><li><p>the table position matches the plan</p></li></ul><p></p>

Check the site is ready:

  • access

  • level floor

  • the table position matches the plan

2
Step 2 of 10
<ul><li><p>Unpack and check the part count</p></li><li><p>Photograph any transit damage before you start</p></li></ul><p></p>

  • Unpack and check the part count

  • Photograph any transit damage before you start

3
Step 3 of 10
<p>Assemble the base upright:</p><ul><li><p>Stand the leg sets up</p></li><li><p>Push the modesty panel down onto the Striplox</p></li><li><p>Then fit the centre bracket on each leg set with 25 mm wood screws (it is packed in the fixings bag)</p></li></ul><p></p>

Assemble the base upright:

  • Stand the leg sets up

  • Push the modesty panel down onto the Striplox

  • Then fit the centre bracket on each leg set with 25 mm wood screws (it is packed in the fixings bag)

4
Step 4 of 10
<p>Check every base joint is flush with no gaps.</p>

Check every base joint is flush with no gaps.

5
Step 5 of 10
<p>Set the base in its final position, standing on its glides.</p>

Set the base in its final position, standing on its glides.

6
Step 6 of 10
<p>Single-piece tops:</p><ul><li><p>Lift the top onto the base (two-person lift minimum)</p></li><li><p>Locate each mount plate in its pocket rebate</p></li></ul><p></p>

Single-piece tops:

  • Lift the top onto the base (two-person lift minimum)

  • Locate each mount plate in its pocket rebate

7
Step 7 of 10
<p>Dry-join tops:</p><ul><li><p>Place the first top section on the base, then the second</p></li><li><p>Fit the biscuits and push the sections together</p></li><li><p>Tighten the bench-top connectors from underneath</p></li></ul><p></p>

Dry-join tops:

  • Place the first top section on the base, then the second

  • Fit the biscuits and push the sections together

  • Tighten the bench-top connectors from underneath

8
Step 8 of 10
<p>Working from underneath, fix up through each mount plate into the top with 25 mm black hex screws.</p>

Working from underneath, fix up through each mount plate into the top with 25 mm black hex screws.

9
Step 9 of 10
<p>Check:</p><ul><li><p>the table is stable</p></li><li><p>the top is seated in all the pockets</p></li></ul><p></p>

Check:

  • the table is stable

  • the top is seated in all the pockets

10
Step 10 of 10
<p>Hand over:</p><ul><li><p>Clean the table</p></li><li><p>Do a final inspection</p></li><li><p>Take photos</p></li><li><p>Get sign-off</p></li></ul><p></p>

Hand over:

  • Clean the table

  • Do a final inspection

  • Take photos

  • Get sign-off